Lo-Chlor Starver X Phosphate Remover - 1 Litre

Based on 0 reviews. - Write a review

£33.95

Stock: In Stock
Model: 1lt
Weight: 1.00kg
SKU: R3-7LKT-MPHF
MPN: LCC-500-0561

Lo-Chlor

Add to Cart

Buy Now Ask Question

Add to Wish List Compare this Product

Lo-Chlor Starver X

1 Litre

Neutralises and removes dissolved phosphates in 24 hours

Ideal for pools with a phosphate level over 2ppm

Great shock treatment for phosphate at spring open up

General
Dose rate	<table> <thead> <tr> <th scope="col">Litres</th> <th scope="col">Gallons</th> <th scope="col"> <p>Lower by </p> <p>up to 6ppm</p> </th> <th scope="col"> <p>Lower by </p> <p>up to 1ppm</p> </th> </tr> </thead> <tbody> <tr> <td>25,000</td> <td>5,500</td> <td>500ml</td> <td>84ml</td> </tr> <tr> <td>50,000</td> <td>11,000</td> <td>1000ml</td> <td>168ml</td> </tr> <tr> <td>75,000</td> <td>16,500</td> <td>1500ml</td> <td>252ml</td> </tr> </tbody> </table> <p> </p>
General Instructions	<p><strong><em>If algae is present, it is recommended you treat this algae first with one of the Lo-Chlor Algaecides prior to beginning phosphate removal.</em></strong></p> <p>Clean or backwash filter and ensure pool water is balanced.</p> <p>Shake the container well before use.</p> <p>Slowly add the required amount of Starver® X to the pool water directly in front of the skimmer box inlet.</p> <p>It is recommended that immediately following the addition of Starver® X, place one Lo-Chlor Miraclear Pool Clarifier Cube directly into the pump basket (follow package directions). The addition of a Miraclear Pool Clarifier Cube will reduce any cloudiness associated with phosphate removal.</p> <p>Run filtration system continuously for 24 hours. Check filter pressure regularly and backwash, if necessary.</p> <p>Test phosphate level of pool water at least 24 hours after treatment.</p> <p>If necessary, repeat additional dosages at weekly intervals until phosphate level is within acceptable range. For faster results, Starver® X dosage can be repeated at 24-hour intervals.</p> <p><strong>N.B.</strong> After treatment regularly check phosphate levels in your pool. For ongoing control and treatment of phosphates use Lo-Chlor Starver®.<strong> </strong></p> <p><span style="background-color: transparent;">For Use in Natural Swimming Pools and Ponds</span></p> <p>With no aquatic life present our phosphate removal products can be dosed at the maximum approved dosing rates using the following instructions:</p> <p>Backwash the filter.</p> <p>Calculate the required dose to lower the PO4 close to zero.</p> <p>Add the required dose to a clean watering can and/or clean pump sprayer.</p> <p>Add fresh water to the equivalent volume of 5 times the required dose rate and mix thoroughly. For example, 500ml of product requires a minimum of 2.5L of water.</p> <p>Add the product ensuring maximum dispersion across the section of water. DO NOT dump into one area!</p> <p>Phosphate levels should be checked a minimum of 24 hours after treatment.</p> <p>Re-test the PO4 level and repeat as necessary.</p> <p>If there is aquatic life present Starver® X can only be dosed to remove a maximum of 1ppm per treatment. This is due to the sensitivity of aquatic life. If aquatic life is present then please use the following instructions:</p> <p>Backwash the filter.</p> <p>Calculate the required dose to remove 1ppm. In a 50m3 pool/pond a dose of only 167ml of product is required.</p> <p>Add the required dose to a clean watering can and/or clean pump sprayer.</p> <p>Add fresh water to the equivalent volume of 5 times the required dose rate and mix thoroughly. For example, 167ml of product requires a minimum of 835ml of water.</p> <p>Add the product ensuring maximum dispersion across the section of water. DO NOT dump into one area!</p> <p>Phosphate levels should be checked a minimum of 24 hours after treatment.</p> <p>Re-test the PO4 level and repeat as necessary.</p> <p>We recommend a proactive approach to phosphate control therefore once you have obtained a PO4 level of 0.5ppm we recommend a weekly dose thereafter to remove this amount.</p> <p>For Use in Aquarium</p> <p>The dose rate on a bottle of Starver® X is based on removing phosphate from a swimming pool. If you are using Starver® X in an aquarium then please use the following instructions:</p> <p>Prior to dosing make sure that any filters in your aquarium are thoroughly cleaned.</p> <p>For initial doses (until phosphate levels are at zero) apply 3ml of product per 100 litres of aquarium water.</p> <p>Repeat this dose every 4 days until your phosphate level reaches zero.</p> <p>If any corals present show sign of stress, wait 7 days prior to dosing again.</p> <p>Once your phosphate level is at zero then use a maintenance dose of 3ml per 200 litres of aquarium water on a weekly basis</p> <p>Please Note:</p> <p>The activity of Lo-Chlor Starver® X will depend on your filtration.</p> <p>If high levels of phosphate are present, the aquarium water may turn slightly cloudy – this will clear.</p> <p>Always ensure that calcium levels are maintained to reduce any possible coral stress.</p> <p>Always use an accurate phosphate test kit.</p>

Lo-Chlor Starver X Phosphate Remover - 1 Litre

Write a review

Information

My Account

Customer Service